6 DIFFERENT METHODS OF BORING USED FOR SOIL EXPLORATION

Boring Methods of Exploration  

The boring methods are used for exploration at greater depths where direct methods fail. These provide both disturbed as well as undisturbed samples depending upon the method of boring. In selecting the boring method for a particular job, consideration should be made for the following:

  • The materials to be encountered and the relative efficiency of the various boring methods in such materials
  • The available facility and accuracy with which changes in the soil and ground water conditions can be determined
  • Possible disturbance of the material to be sampled

The different types of boring methods are:

  1. Displacement boring
  2. Wash boring
  3. Auger boring
  4. Rotary drilling
  5. Percussion drilling
  6. Continuous sampling

1. Displacement Boring

It is combined method of sampling & boring operation. Closed bottom sampler, slit cup, or piston type is forced in to the ground up to the desired depth. Then the sampler is detached from soil below it, by rotating the piston, & finally the piston is released or withdrawn. The sampler is then again forced further down & sample is taken. After withdrawal of sampler & removal of sample from sampler, the sampler is kept in closed condition & again used for another depth.

Features

  • Simple and economic method if excessive caving does not occur. Therefore not suitable for loose sand.
  • Major changes of soil character can be detected by means of penetration resistance.
  • These are 25mm to 75mm holes.
  • It requires fairly continuous sampling in stiff and dense soil, either to protect the sampler from damage or to avoid objectionably heavy construction pit.

2. Wash Boring

It is a popular method due to the use of limited equipments. The advantage of this is the use of inexpensive and easily portable handling and drilling equipments. Here first an open hole is formed on the ground so that the soil sampling or rock drilling operation can be done below the hole. The hole is advanced by chopping and twisting action of the light bit. Cutting is done by forced water and water jet under pressure through the rods operated inside the hole.

In India the “Dheki” operation is used, i.e., a pipe of 5cm diameter is held vertically and filled with water using horizontal lever arrangement and by the process of suction and application of pressure, soil slurry comes out of the tube and pipe goes down. This can be done upto a depth of 8m –10m (excluding the depth of hole already formed beforehand).

Just by noting the change of colour of soil coming out with the change of soil character can be identified by any experienced person. It gives completely disturbed sample and is not suitable for very soft soil, fine to medium grained cohesionless soil and in cemented soil.

Wash Boring
Wash Boring

3. Auger Boring

Augers
Augers

This method is fast and economical, using simple, light, flexible and inexpensive instruments for large to small holes. It is very suitable for soft to stiff cohesive soils and also can be used to determine ground water table. Soil removed by this is disturbed but it is better than wash boring, percussion or rotary drilling.

This method of boring is not suitable for very hard or cemented soils, very soft soils, as then the flow into the hole can occur. This method is also not suitable for fully saturated cohesionless soil.

4. Rotary Drilling

Rotary drilling method of boring is useful in case of highly resistant strata. It is related to finding out the rock strata and also to access the quality of rocks from cracks, fissures and joints. It can conveniently be used in sands and silts also. Here, the bore holes are advanced in depth by rotary percussion method which is similar to wash boring technique. A heavy string of the drill rod is used for choking action. The broken rock or soil fragments are removed by circulating water or drilling mud pumped through the drill rods and bit up through the bore hole from which it is collected in a settling tank for recirculation. If the depth is small and the soil stable, water alone can be used. However, drilling fluids are useful as they serve to stabilize the bore hole.

Drilling mud is slurry of bentonite in water. The drilling fluid causes stabilizing effect to the bore hole partly due to higher specific gravity as compared with water and partly due to formation of mud cake on the sides of the hole. As the stabilizing effect is imparted by these drilling fluids no casing is required if drilling fluid is used.

This method is suitable for boring holes of diameter 10cm, or more preferably 15 to20cm in most of the rocks. It is uneconomical for holes less than 10cm diameter. The depth of various strata can be detected by inspection of cuttings.

Rotary Drilling System
Rotary Drilling System

5. Percussion Drilling

Percussion Drilling
Percussion Drilling

In case of hard soils or soft rock, auger boring or wash boring cannot be employed. For such strata, percussion drilling is usually adopted. Here advancement of hole is done by alternatively lifting and dropping a heavy drilling bit which is attached to the lower end of the drilling bit which is attached to the cable.

Addition of sand increases the cutting action of the drilling bit in clays. Whereas, when coarse cohesionless soil is encountered, clay might have to be added to increase the carrying capacity of slurry.

After the carrying capacity of the soil is reached, churn bit is removed and the slurry is removed using bailers and sand pumps. Change in soil character is identified by the composition of the outgoing slurry.

The stroke of bit varies according to the ground condition. Generally, it is 45-100cm in depth with rate of 35-60 drops/min.

It is not economical for hole of diameter less than 10cm. It can be used in most of the soils and rocks and can drill any material.

One main disadvantage of this process is that the material at the bottom of the hole is disturbed by heavy blows of the chisel and hence it is not possible to get good quality undisturbed samples. It cannot detect thin strata as well.

6. Continuous Sampling

The sampling operation advances the borehole and the boring is accomplished entirely by taking samples continuously. The casing is used to prevent the caving in soils. It provides more reliable and detail information on soil condition than the other methods. Therefore it is used extensively in detailed and special foundation exploration for important structures.

It is slower method and more expensive than intermittent sampling. When modern rotary drilling rigs or power driven augers are not available, continuous sampling may be used to advantage for advancing larger diameter borings in stiff and tough strata of clay and mixed soil.

In the Boston district, corps of Engineers has made faster progress and reduced cost by use of continuous sampling in advancing 3-inch diameter borings through compact gravelly glacial till, which is difficult to penetrate by any boring method.

Author

Dr. Deepankar Choudhury (IIT Bombay)

Source (NPTEL)

12 thoughts on “6 DIFFERENT METHODS OF BORING USED FOR SOIL EXPLORATION”

  1. The type of drilling one of which has an effect on the quality of the sample obtained and the difference in the use of rods with complete shafts and not with shafts has an effect on the high or low level of contamination of the sample results. How about that’s?

    Reply
  2. I did not realize that there were several different methods of soil boring. It sounds like wash boring is a good technique if equipment is scarce. I think it would be wise to make a plan before starting a project to choose which boring type is the most efficient.

    Reply
  3. actually i required meterial of GROUND IMPROVEMENT TECHNIQUES. no one can provide this type of sollution thats why i humble request to contact me on my email ID.

    Reply

Leave a Comment